廣東瑩瞬超高精密磨床特性:
1、研磨精度提高grinding accuracy improved
瑩瞬磨床工作臺面精度保證150×400mm(試磨片x6片,其高度差為0.002mm),研磨表面光潔度為Ra0.18,切溝槽之能力同向誤差100㎜,2μm內。
150 x 400mm ensure transient working table surface precision grinder Ying (test plate X6, the height difference is 0.002mm), grinding surface roughness is Ra0.18, the ability to cut grooves with error of 100 mm, 2 m.
2、高精度之直結式主軸high precision straight spindle
瑩瞬磨床主軸采用直結式設計,搭配CP4級精密斜角滾珠軸承、V3級低震動馬達與動平衡后,為普通型主軸之三倍剛性,直接安裝于機頭座上,更加強頭部之強度,保證主軸之偏轉遠低于0.002mm;為主軸在超精密磨屑中的精度保證及硬質合金正切削時提供充足的動力。
The design of direct drive by Ying transient CP4 precision grinder spindle, collocation angle ball bearing, V3 low vibration motor and the dynamic balance, is a common type of spindle three times of rigid, directly mounted on the headstock, the head of the more strong strength, ensure the deflection spindle is much lower than that of 0.002mm; for the spindle in ultra precision grinding accuracy ensure the chip and the hard alloy with sufficient power is cutting.
3、高剛性、高強度鑄件體high rigidity and high strength casting body
瑩瞬磨床主機座、工作臺、滑座、立柱及機頭等各重要鑄件體均采用高級鑄鐵FCD300,并經由有限元分析與計算,達到剛性倍增與質量的工程需求,每件鑄件均經過內應力消除處理,確保長久不變形,并具極佳的抗彎及抗扭應力,確保機床長時間之研削精度。
The host seat, casting Ying instantaneous grinder worktable, a sliding seat, column and machine body adopts advanced iron FCD300, and through the finite element analysis and calculation, to achieve rigid multiplication and engineering demand quality, each piece of casting after treatment to eliminate internal stress, ensure long-term deformation, bending and torsion and with excellent stress, ensure the long time of precision grinding machine.
4、高傳動超輕滑動之工作臺硬軌結構hard rail structure of high transmission and super light sliding table
瑩瞬磨床前后雙V,左右1V一平,均貼附U.S.A耐磨片TURCITE-B,以及手工精密鏟花。保證工作臺在負荷的情況下,不僅減低阻尼系數,且滑動順暢、耐磨,確保移動輕快與精度準確,適合成型超精密研磨。
Ying Heng grinding machine before and after double V, around 1V flat, are affixed with U.S.A wear-resistant film TURCITE-B, as well as hand precision shovel flowers. To ensure that the work platform in the case of load, not only reduce damping coefficient, and smooth sliding, wear-resistant, to ensure smooth and accurate movement, the most suitable for forming ultra precision grinding.
5、自動潤滑油路設計automatic lubrication circuit design
瑩瞬磨床采用循環式中心潤滑過濾裝置,一方面對機床所有傳動螺桿和滑動面均得到之潤滑,另一方面對機床進行不間斷潤滑油循環過濾,更好的保證機床的使用壽命。
The use of circular grinder Ying instantaneous center lubricating filter device, a machine tool in all drive screw and the sliding surface are the best lubrication, the other side face of machine tool for uninterrupted lubricating oil filtration cycle, better service life assurance machine.
6、電氣控制、圖型化操作面板electrical control and graphical operation panel
瑩瞬磨床專業設計電氣控制系統,符合3C歐洲CE安全要求,采用國際知名品牌的電氣組件。固定式操作面板設計,操控集中于操作面板上,符合人體工學,操作面版采圖型化設計,功能一目了然,操作簡便易學。
It is specialized in the design of electrical control systems, in line with 3C European CE safety requirements, the use of internationally renowned brands of electrical components. The design of the fixed operation panel focuses on the operation panel, and conforms to the ergonomic design. It is easy to read and easy to operate.
機床數據/型號 Machine data / model | 單位 Company | YS-450 |
工作臺面積 Table area | mm | 150×450 |
研磨最大長度 Maximum grinding length | mm | 465 |
研磨最大寬度 Maximum grinding width | mm | 160 |
砂輪軸心至工作臺距離Distance between grinding wheel axis and table | mm | 400 |
左右手動行程 Left hand travel | mm | 465 |
前后手動行程 Manual travel | mm | 170 |
前后手輪(每刻度)(of time) before and after the handwheel | mm | 0.02 |
前后手輪進刀量(每轉一圈)Front and rear handwheel feed (per turn) | mm | 5 |
上下手輪(每刻度) On the handwheel (moment of) | mm | 0.005 |
上下手輪進刀量(每轉一圈)Feed amount on the upper wheel (one turn per turn) | mm | 1 |
砂輪尺寸(外徑×寬度×孔徑)Wheel size (outer diameter * width * aperture) | mm | 180×16×31.75 |
主軸速度(60HZ/50HZ) Spindle speed (60HZ/50HZ) | rpm | 3600/3000 |
主軸馬達(V3級) Spindle motor (class V3) | HP | 1.5 |
吸塵/水泵 馬達 Suction / pump motor | kw/w | 0.37kw/40w |
機床重量(約) Machine weight (approx.) | KG | 900 |
機床外形尺寸 長×寬×高Dimensions of machine tool length * width * height | mm | 1500×1100×1850 |
※本公司由于技術研究改進之需要,因此保有更改設計和制造權利,上述規格若有更改恕不另行通知